{"id":536,"date":"2026-10-14T10:47:42","date_gmt":"2026-10-14T02:47:42","guid":{"rendered":"http:\/\/www.konturm.com\/blog\/?p=536"},"modified":"2026-10-14T10:47:42","modified_gmt":"2026-10-14T02:47:42","slug":"how-does-solar-mounting-work-in-areas-with-high-snowfall-42e5-e0d752","status":"publish","type":"post","link":"http:\/\/www.konturm.com\/blog\/2026\/10\/14\/how-does-solar-mounting-work-in-areas-with-high-snowfall-42e5-e0d752\/","title":{"rendered":"How does solar mounting work in areas with high snowfall?"},"content":{"rendered":"

If you\u2019ve ever driven through a mountain town in the thick of winter, you\u2019ve probably seen solar panels tilted sharply upward, sticking out from under banks of untouched snow like stubborn green-and-blue flags. For a long time, people in areas with heavy snowfall wrote off solar power as a pipe dream\u2014snow would cover panels for months, killing output, and heavy snow loads would bend or break racking like wet cardboard. As a solar mounting supplier, I\u2019ve spent the last 12 years on the ground in Vermont, upstate New York, and parts of northern Pennsylvania, solving exactly these problems, and I\u2019m here to break down how solar mounting works in high-snow areas without the jargon that makes most homeowners zone out. Solar Mounting<\/a><\/p>\n

<\/p>\n

First, let\u2019s get one myth out of the way: snow doesn\u2019t have to mean the end of solar power. I\u2019ve installed systems that put out 70-80% of their summer production in the dead of a snowy Vermont January, and the key isn\u2019t just the panels\u2014it\u2019s how they\u2019re mounted. The biggest mistake new installers make in high-snow zones is using the same flat, low-tilt racking you\u2019d use in Arizona. That works for snow that slides off easily, but for areas that get 6 feet of snow a year or more, you need two non-negotiable design choices: tilt angle and rack strength.<\/p>\n

Let\u2019s start with tilt. It\u2019s not just about getting the most sun in summer\u2014though that matters too. In high-snow areas, tilt is calculated to help snow slide off naturally, without you having to climb a ladder and shovel panels every time it snows. We do this by using a base tilt of 30 to 35 degrees for most of our northern U.S. and Canadian customers, which is steeper than the 15 to 20 degrees you see in sunbelt states. Here\u2019s the science bit: snow\u2019s angle of repose\u2014meaning the steepest slope it can sit on before sliding\u2014is roughly 30 degrees. If your panel is tilted at 32 degrees, fresh, powdery snow (the kind that falls in mid-winter) will slide off almost immediately after it stops snowing. Wet, heavy spring snow might take a day or two, but that\u2019s way better than a flat panel holding 100 pounds of snow for weeks.<\/p>\n

I learned this the hard way early in my career. In 2012, I installed a system for a family in Stowe, Vermont, using a standard 18-degree tilt because that\u2019s what our default spec sheet said. That winter, they got 7 feet of snow, and the panels were covered solid for six weeks. The following year, we re-mounted them at 33 degrees, and that January, snow was gone from the panels in 48 hours. The homeowner saved $1,200 that month in electric bills alone, and that\u2019s when I realized tilt isn\u2019t a one-size-fits-all number\u2014it\u2019s tailored to the snowfall of the exact zip code. We even adjust it a little for elevation: mountain towns get more heavy, wet snow, so we bump tilt to 35 degrees, while lower valleys with drier snow can get away with 30.<\/p>\n

Next up is rack strength, and this is where cheap, imported mounting systems fall flat. When I say rack strength, I\u2019m not just talking about holding snow\u2014 I\u2019m talking about withstanding the weight of 2 feet of wet snow, which can weigh 20 to 30 pounds per square foot, plus ice, wind, and the occasional falling tree branch or snowplow debris. Most low-end racking uses thin aluminum rails with 1.5-inch walls, which bend under just 15 pounds per square foot. That\u2019s fine for light snow in California, but not for Minnesota or Maine. Our racking uses rails with 3-inch walls, hot-dip galvanized steel for the base, and we design every system to hold a minimum load of 50 pounds per square foot\u2014way more than the heaviest recorded snow load in the lower 48.<\/p>\n

Wait, but what about all that ice that forms around panels? I get that question all the time. Ice is trickier than snow because it sticks to panels, not just sits on them. Our solution is two-fold: first, we space panels 6 to 12 inches apart vertically, depending on height. That lets sunlight hit the back of the panel and create a small air gap between the panel and the snow\/ice, helping it melt from both top and bottom. Second, we use custom clip-on heat tape for customers who deal with frequent ice dams\u2014no need for full panel heating, which uses too much electricity. The heat tape only warms the edge of the panel, where ice usually forms, and it\u2019s powered by the system\u2019s own output when it\u2019s running, so it barely impacts net production.<\/p>\n

Another big thing we design for in high-snow areas is clearance above the roof. A lot of homeowners want panels mounted flush to the roof to save on cost, but that\u2019s a disaster in snow zones. When snow slides off a panel and hits the roof, it can slide under the shingles and cause ice dams, or even damage gutters. We mount panels 18 to 24 inches above the roof surface for steep roofs, and up to 30 inches for low-slope roofs. That extra space gives snow a place to fall without damaging the roof, and it also lets more wind circulate under the panels, which helps melt snow faster. Wind is a secret weapon here\u2014wind moving between the panel and the roof creates convection, like the gap in a double-pane window, and that convection speeds up snow melt by 20-30% compared to flush-mounted panels.<\/p>\n

I also get asked about snow guards\u2014those little plastic or metal pads that sit on roof shingles to keep snow from sliding all at once. For solar panels, we don\u2019t use regular snow guards, but we do integrate our own custom ones into the racking design. We place 2-foot long rubber stops on the lower edge of the panel rack to slow down snow slides just enough that it falls in small chunks, not avalanches that could take out gutters, satellite dishes, or even people walking below. A customer in Burlington had a bad experience in 2017 when a full roof of snow slid off a neighbor\u2019s house and crushed their garden shed. Now all our systems have those rack-integrated guards, and we always add an extra set for customers who have decks or patios below their panels.<\/p>\n

Let\u2019s talk about a common misconception: some people think that solar panels in snow are less efficient because cold air makes them work harder. That part is true\u2014panels actually perform better in cold weather, because high temperatures lower their efficiency. A panel that produces 250 watts at 70 degrees might put out 260 watts at 20 degrees. The catch is when snow covers the surface, blocking sunlight. But with the tilt and spacing we use, that snow cover is almost always temporary. Even in northern Maine, where winters are long, we\u2019ve seen our systems have an average output of 75% of their summer production, compared to 40% for systems with standard low-tilt racking.<\/p>\n

I want to be transparent, too\u2014no system works 100% of the time. If you get a 2-foot blizzard that lasts three days, some snow will stick. But that\u2019s where regular maintenance comes in, and it\u2019s way less work than shoveling your roof every winter. We recommend customers do one quick check a month during the peak snow season, and if there\u2019s thick snow covering panels that\u2019s been there for more than 48 hours, you can gently brush it off with a soft broom\u2014no need to climb on the roof, we sell lightweight, pole-mounted brushes that let you reach from the ground. The worst thing you can do is use a shovel or ice pick, which can scratch or crack the panel surface.<\/p>\n

Over the last 12 years, I\u2019ve installed more than 2,000 solar systems in snow-heavy areas, and the feedback I get most often is that customers are surprised by how little hassle solar is in winter. Last year, a customer in Park Rapids, Minnesota, told me he barely noticed the snow\u2014by the time he\u2019s ready to run the snowblower in the morning, his panels are already clear enough to power the garage and the kitchen. That\u2019s the point of good solar mounting: it doesn\u2019t just work around snow, it works with it. The tilt lets gravity do the work, the strong racking handles the weight, and the spacing and clearance leverage wind and cold to keep output high when you need it most.<\/p>\n

If you\u2019re a homeowner in a high-snow area considering solar, don\u2019t let old myths or bad installer experiences scare you off. The key is finding a solar mounting supplier that has actual experience in your climate, not just a spec sheet written for a warm, flat state. We don\u2019t do one-size-fits-all designs\u2014we look at your zip code, your roof\u2019s slope, your average snow load, and even the trees around your property to build a system that works for your specific winter.<\/p>\n

If you\u2019re ready to learn more about what a snow-ready solar system would look like for your home, reach out to us to discuss your project. We can send a local rep to walk your property, answer your questions, and give you a custom quote tailored to your area\u2019s snow and weather conditions. There\u2019s no pressure, and we\u2019ll be honest if solar isn\u2019t the right fit for your roof\u2014we\u2019ve been doing this long enough to know when a system will thrive and when it needs a little extra tweaking.<\/p>\n

<\/p>\n

So next time you see solar panels on a snowy mountain town roof, take a look at how they\u2019re tilted. Chances are, the installer didn\u2019t just pick a number at random\u2014they accounted for snow, weight, and sun, just like we do. That\u2019s the real work of solar mounting in high-snow areas: it\u2019s not about fighting winter, it\u2019s designing a system that works with it, so you can keep saving money all year long.<\/p>\n

Solar Mounting<\/a> References<\/p>\n

    \n
  1. National Renewable Energy Laboratory. (2021). Snow Loads and Solar Panel Performance in Cold Climates. U.S. Department of Energy.<\/li>\n
  2. International Code Council. (2022). Solar Installation Standards for Snow-Load Regions. ICC 2022 Building Code Supplement.<\/li>\n
  3. Solar Energy Industries Association. (2020). Best Practices for Solar Mounting in High-Snow Zones. SEIA Technical Bulletin TB-007.<\/li>\n
  4. University of Minnesota Extension. (2019). Solar Energy for Cold and Snowy Climates: Design Considerations and Maintenance Tips. Extension Publication 10122.<\/li>\n<\/ol>\n
    \n

    Xiamen D.T. Multi Tech Co., Ltd.<\/a>
    Xiamen D.T. Multi Tech Co., Ltd. is one of the most professional solar mounting manufacturers and suppliers in China, we’re featured by quality products and good service. Please rest assured to wholesale cheap solar mounting from our factory.
    Address: No.102-10, Dongdu Road, Huli District, Xiamen, Fujian Province, China.
    E-mail: deven@deven-tina.com
    WebSite:     https:\/\/www.dtsolarpower.com\/<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"

    If you\u2019ve ever driven through a mountain town in the thick of winter, you\u2019ve probably seen … How does solar mounting work in areas with high snowfall?<\/span>Read more<\/a><\/p>\n","protected":false},"author":308,"featured_media":536,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[499],"class_list":["post-536","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-industry","tag-solar-mounting-46f3-e19c73"],"_links":{"self":[{"href":"http:\/\/www.konturm.com\/blog\/wp-json\/wp\/v2\/posts\/536","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/www.konturm.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.konturm.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.konturm.com\/blog\/wp-json\/wp\/v2\/users\/308"}],"replies":[{"embeddable":true,"href":"http:\/\/www.konturm.com\/blog\/wp-json\/wp\/v2\/comments?post=536"}],"version-history":[{"count":0,"href":"http:\/\/www.konturm.com\/blog\/wp-json\/wp\/v2\/posts\/536\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"http:\/\/www.konturm.com\/blog\/wp-json\/wp\/v2\/posts\/536"}],"wp:attachment":[{"href":"http:\/\/www.konturm.com\/blog\/wp-json\/wp\/v2\/media?parent=536"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.konturm.com\/blog\/wp-json\/wp\/v2\/categories?post=536"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.konturm.com\/blog\/wp-json\/wp\/v2\/tags?post=536"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}